Treatment of raw materials → adding auxiliary materials → mixing → pellet making → drying → whole grain → tablet pressing
Machine operation:
Open the electric box door, close the power switch, the indicator light on the operation panel, press the start button, the indicator light slowly rises, the speed will be gradually added, if you need to stop the emergency, press the "stop" button, the tablet press will stop running immediately. After pressing, open the electric box door and cut off the power supply.
Operation Skills
Before using the tablet press, all oil cups, oil holes and friction surface must be added with lubricating oil, and empty operation so that the friction surface is covered with oil film, prolong the service life of the machine.
2 Before and after each shift must be air pressure test, no problem after the opening of electric pressing, so as to prolong the service life of the mold. Selection of 3 pieces (mold) : The working end face of the upper and lower punch of the tablet die forms the surface shape of the tablet, and the aperture of the middle mold is the diameter of the tablet. The correct choice of sheet type is a successful step of die pressing. For example, chewable tablets require higher hardness and are convenient to chew. Most choose bevel type flat tablets; Thin film coating can be selected shallow concave. Since there is no adhesive and lubricant in the raw materials of Chinese medicine tablets, the pressure should be large when pressing the tablets, and the tablet type should be shallow concave. For tablets with high sugar content, the tablet design should be shallow concave or flat. Medium die can use alloy steel or hard alloy. Deep concave die die is easy to damage, as little as possible.
4. When replacing the mold, if the middle mold cannot go down, use a rod of the same size as the upper mold to gently knock the middle mold down.
5 In the process of tablet pressing, the quality of tablets (tablet weight, hardness, surface finish, etc.) must be checked frequently and timely adjusted.
6 If pressing mineral, plant fiber content is large, large diameter, poor viscosity of the material, it is appropriate to use low speed tablet. High speeds generally do not exceed 25 RPM. On the contrary, if the viscosity, good liquidity, small size, easy to form particles, you can choose a higher speed. Mold preservation method: After cleaning, coated with a layer of food grade lubricating oil (oil, cooking oil can be), put into a special protective box or die storage box, put on the shelf, should be marked with the size, on the shelf preservation. 8 When the tablet pressing chamber is operated or not, it shall be closed with plexiglass to prevent contamination.
Take out the remaining powder and clean all parts of the machine after use every day. If the deactivation time is long, it is necessary to remove the die, the machine each friction surface. Clean the working surface, coat it with antirust oil, cover it with dust jacket; The die should be wiped clean and kept in oil.
Precautions
1 Before the first use, the machine should be carefully read the manual, and then use. Do not touch the tablet press chamber with hands or other tools during operation.
3. Materials shall not contain metal or solid materials to avoid damage to the mold.
4 Turn off the power when replacing the mold.
When the sound of the machine is abnormal, the power supply should be turned off and then checked.
6 When the machine is not operated for a long time, the mold should be unloaded and stored separately.
The pelleting process before laminating has a great influence on laminating. For example, the formulation of granulation of pharmaceutical materials and sliding materials, fillers, binders and other auxiliary materials (powder condition, particle tightness, powder fraction, water content, etc.) has a direct impact on the amount of tablets. And often due to the ingredients of improper granulation can not be made into pieces, and even damage the machine. Therefore, this machine can not be used for semi-solid or wet or no granular very fine powder tablet. In use, if it is found that the pressure has been adjusted to a considerable extent, the pressure is still not tablet, or although the pressure is tablet, it appears too loose, layer, debris, pitting, powder and other phenomena. Should be ingredients and other aspects to find out the reason, to solve. Do not blindly adjust and increase the pressure, and even damage the machine. In addition, some drugs pressed out of the pill hardness is not large, but has a certain toughness, the mess is not bad (usually from the height of 1-1.2 meters to fall on the ground is not broken), so should meet the requirements of transportation storage for the degree not only from the hardness of the eye, so as not to press the tablet pressure is too large, damage the machine. 1. What about the quality of your tablet press?
Our factory has more than 10 years of machining experience; All of our machines have obtained ISO9001, SGS and CE certificates. Has been exported to many countries and regions; We have a good reputation from our customers.
2. What about the price of your tablet press?
We always regard quality as the life of the factory, no matter the price is good or bad for us. Quality first, on the basis of first-class quality, ensure that you get a reasonable price!
3. How can we guarantee the quality of the machine after we place the order?
Before delivery, we will send you the pictures and video of the machine, or you can come to us for quality inspection, or you can contact the third party inspection agency for quality inspection.
4. Are your machines delivered safely? Our machines and moulds are exported to all over the world, especially to European and American countries. Our delivery experience enables all customers to safely receive our products.
5. Learn more about our company
6. Can the Electric machines be customized for different voltages and plugs if I decide to buy Automatic Pill Press instead ?
){kind=link}
){kind=link}