Business Type: Manufacturer/Factory
Dongguan, Guangdong, China
|Chamber materials||1.inner wall: SUS304 stainless steel plate.|
2. bottom board: SUS304 stainless steel plate and it's reinforced by the well type
high strength square pipe.
3. External: cold rolled steel with power coated; power coated after cleaning and
|Insulation materials||The thickness of the insulating layer of inner box is 100mm, and the fire resistance |
material is high strength PU polyurethane foam insulation(which is more thermal and
refractory than common PU);
thermal insulation coefficient: less than 0.0212kcal/m.hr, and the layer with fire
protection design; the insulation layer has high temperature resistance rock wool
plus fire gypsum layer which can guarantee the thermal insulation materials doest not
melt and burn although catch fire during test.
|Pressure balancing port||An electronic pressure balance with controllable pressure. The device can keep the |
pressure balance inside and outside of test chamber at any time under the conditions
of high temperature, high humidity and wet freezing cycle, and avoid the expansion
of the chamber caused by the increase of the pressure.
|There are environmental safety production and explosion-proof safety protection and |
explosion venting function could ensure that the battery fire or explosion in any case,
will not harm to people and the environment. Automatic alarm linkage typeFM200
total flooding extinguishing system.
|Intake and exhaust |
|The test chamber is equipped with 1 set of inlet and exhaust device, you can |
manually control the exhaust action through the operation panel switch to intake a
large number of air rapidly to discharge the harmful gas in test chamber to outside
of the laboratory through the air duct . In order to avoid the harmful gas harm people.
|Control panel||Using 10 inch Chinese color LCD touch type man-machine interface and high performance |
programmable logic controller(PLC), fault indication lamp, adjustable over temperature
protection, total power switch and USB interface.
|subequipment||a set of subequipment, material SUS304 stainless steel, high temperature resistance |
-70ºC~+150ºC, nontoxic and odorless in high temperature;
|1. temperature and |
|Armored platinum resistor PT100 Germany JUMO; |
Humiditu sensor: Finland VAISALA0.8 class humidity module sensor,
humidity range 0-100%RH, temperature range: -100-200 ºC.
|2. Touch screen||Adopt 10 inch color LCD touch type man-machine interface.|
|3. Showing contents||It can input, display and control the temperature directly. It is equipped with the special |
software of our company's test chamber, and the control system adopts the man-machine
dialogue mode. It has automatic, intelligent and humanized design. The control system
can display and set the test parameters, program curves, operating time, the working
state of the heater, chiller and blower. At the same time with the test procedures for
automatic operation and PID parameters self turning function; automatic combination
heating system, cooling system, circulating fan, over-temperature alarm system,
so as to ensure the high quality of the temperature control system.
The main parts are SCHNEDER brand.
Temperature display accuracy is 0.01 ºC and analytical precision control is 0.001.
|4.Software||Software V1.0. Machine records of curves and date can be stored computer and |
networked use,storage date can not be changed, you can alway stransfer date,
in any office can view the date. National computer software copyright registration
certificate no. 0698434, soft landing.
|5. Software integration (optional)||Our company has cooperate with the United States AV, Austria AVL, Gemany Krisler, |
Taiwan CHROMA, Aidekesi and other well known brand company.
And we integrated and controlled with the total control system of the production line,
also we could enter the ERP system according customer's requests. The most mature
case of our company is the charging and discharging motor in new engergy filed,
aging cabinet for Delta and rapid temperature and humidity chamber.
|Inner size: |
|R: -20ºC~150ºC; L: -40ºC~150ºC; U: -60ºC~150ºC|
|Heating time||20→85ºC within 60 minute|
|Colling time||20ºC→rated min. temperature within 60/90/120 minute|
|temp. and |
|BTHC balance adjust temperature(humidity) way.|
|Polyurethane foam plastics compound board(inner: stainless steel pate; |
Outer: galvanized copper plate with power coating.
|Controller||Heater||Nickel chromium alloy electrical heater|
|Mechanical compression single grade refrigerating or |
mechanical compression two element superposition
|full closed or semi-closed compressor|
|Refrigerant||HCFC-22 or HCFC-23|
|Finned heat exchanger|
|10.5" 800*600 dot matrix color LCD touch screen|
|Running mode||Constant running, Program running|
|120 programmable programs; each program have 100 |
steps(paragraph), 10 cycle steps(each step have 99
cycles at most)
|Setting range||Temperature: -100ºC~300ºC ; Humidity: |
|Temperature: 0.01ºC ; Humidity: 0.1%RH*4|
|Print function||Mini-digital printer(optional)|
|Alarm functions of the upper and lower limits, |
self diagnosis, alarm warning, power off protection,
timing fuction(automatic starting and stopping)
|Water supply||Humidity |
| Epuipped with multistage filtering antipenetration water|
purifier(user offer tap water) or user offer distilled
water*4 with resistivity not less than 500Ωm.
|Water supply pressure: 0.2~0.4MPa; |
|Power supply||AC380±10%V 50±0.5Hz 3-phase 4-wire+protective earth line.|
|Electrothermal glass observation window, leading hole(80mm), lighting lamp, |
|Safaty device||Current circuit breaker, dry heating protector(humidifying system), the water system protection,|
the fan overheating protection, compressor overprocess,overheating and overcurrent protection,
open-phase protection, over temperature protection,.
|Welcome to Non-standard,Specail requirements,OEM/ODM orders.|
|GB/T2423.1-2001||test A:low temperature test method|
|GB/T2423.2-2001||test B:high temperature test method|
|GB/T11158-2008||technical condition of high temperature test chamber|
|GB/T10589-2008||technical condition of low temperature test chamber|
|GB/T 2423.22-2008||test Nb:temperature variation test|
|GB/T 2423.4-2008||test Db:alternating temperature humidity test|
|GB/T 31467.1-2015||Lithium-ion power battery packs and systems designed for electromobile part 1: |
high-power applications test specification.
|GB/T 31467.2-2015||Lithium-ion power battery packs and systems designed for electromobile part 2: |
high-power applications test specification.
|GB/T 31467.3-2015||Lithium-ion power battery packs and systems designed for electromobile part 3: |
security requirement and test method.
|GB/T 31484-2015||cycle life-time requirements and test method for Lithium-ion traction battery designed for |
|GB/T 31485-2015||security requirements and test method for Lithium-ion traction battery designed for electromobile|
|GB/T 31486-2015||electrical property requirements and test method for Lithium-ion traction battery designed for |
|GB/T 2423.3-2008||Constant temperature humidity test|
|GJB150.3-2009||high temperature test|
|GJB150.4-2009||low temperature test|
|GJB 150.9A-2009||test standards for temperature humidity test GB/T5170.2-2008 temperature test device.|
|GB/T5170.5-2008||temperature humidity test devices, meet the requirements of 8.1 alternating temperature |
humidity cyclic test in Lithium-ion power battery packs and systems designed electromobile
Part2: test specification for high-energy application.
Products with this tag will be sent out within 15 days after you place an order. For the specific sending time and delivery date, please consult the supplier.
*If the supplier with the above tags do not give you the according discount or service, you can click "Contact Us" to make a complaint. If what you said is true, our professional team will help you to handle this problem.
If you are using our website on PC, you can find us by this way:
Go down to the bottom of Made-in-China.com > Go to "Help" Section> Contact Us
If you are using our Made-in-China.com App, you can find us by this way:
My Account > Click setting section which is in the top right corner > Contact Us