Basic Info.
After-sales Service
Accept
Transport Package
Mastern Carton
Product Description
Visbella® Windshield Repair Kit is very handy to help you to repair the broken windshield in just 20 minutes.This kit will minimize the appearance and stop the spread of chips and cracks in your windshield. It removes air from the break, fills it with durable resin and makes it even stronger than before. For best results, repairs should be made as soon as possible after the damage occurs and before the break is contaminated by dirt or water.
Application:
Repair Car Chips, Stars, Bull Eye, Combinations, Half moon, Crack etc.
KIT INCLUDES
1* 2ml Repair Resin
3* Adhesive Seal
1* Cleaning Cloth
1* Pedestal
5* Curing Film
1* Push Pin
1* Razor Blade
1* Injector with Spring Clip
2* Black O-Ring
Advantages
* Easy to use for all types of lamented windshields
* Minimizes the appearance of chips and cracks in your Windshield
* No heating is required
* Durable resin formula
* Good for multiple repairs
* Single ingredient - eliminates mixing
How to apply?
NOTE:
A. Avoid using in direct sunlight - work in a shaded area.
B. Do not work on a hot windshield,park vehicle in shaded area and open windows to cool glass surface.
C. A safety razor is required to remove components and finish repair.
CAUTION: Avoid any contact with eyes,skin and the body of the vehicle.
KEEP OUT OF REACH OF CHILDREN
Repair Steps
1.Clean out any loose glass particles of the break using a push pin. Replace push pin after use.Clean area surrounding break using a dry cloth.
2.Peel backing off one side of adhesive seal. Line up hole in seal with center of The break. Firmly press the seal to glass.
3.Peel backing from top side of adhesive seal and put black o-ring in the middle of adhesive seal . Line up pedestal with adhesive seal
making sure Tabs match up. Press pedestal to adhesive seal. Run fingers around pedestal to insure a tight bond.
4.Cut tip off resin container and empty about three-fourths of the container resin into the pedestal. It is hard to control but just slowly squeeze. Wipe any excess resin from tip with cloth & save the empty tube for step 8.
5.Insure plunger tip is positioned in injector barrel just above the Pin valve. Press Fit injector into pedestal with the Pin valve lined up with the Tab. Insure connection is tight.Pull plunger upward and lock it by engaging lower notch in plunger with spring clip. Let sit for 10 Minutes.
6.Remove pin valve momentarily to let air in pedestal,then replace pin valve.Hold injector with one hand and ROTATE plunger releasing spring clip from LOWER notch. Depress plunger downward ENGAGE UPPER notch with spring clip. Let sit for 10-15 minutes.
Notes: Insure the plunger in the right starting position while pressure,otherwise the liquid resin inside pedestal may leak from adhesive seal due to big pressure!
7.Remove the injector and loosen outer edges of pedestal with a safety razor. Once top part of pedestal and seal is bent away from glass surface, grip pedestal Tab as shown. Slowly pull up until removed. Wipe and remove excess resin.
8.Slowly squeeze resin container applying several drops of resin into the center of the break area,quickly place a clear curing film over the repair area. Run safety razor lightly over clear film to vent out air bubbles. If possible better to tape the clear film to avoid it slide or being blown away,
9.Cure the resin by using uv light for 2-5 minutes, no limit to the weather. To finish, scrap off excess cured resin and clear film flush with the glass surface using safety razor.
Now step back and admire your work. You know you' ve done a good job when you can't even find the old
chip in the windshield.
If the repair result isn't perfect, just repeat the process until it's smooth and perfect.
If you have any question, just leave us a message or write email to us, we will give you the satisfied reply,
while your problem solved, don't forget write a review and feedback to us.
Address:
No. 1518 Mengxi Road, Huzhou Zhejiang China, Huzhou, Zhejiang, China
Business Type:
Manufacturer/Factory, Trading Company
Business Range:
Chemicals
Management System Certification:
ISO 9001, ISO 14001, BSCI
Company Introduction:
Zhejiang guoneng technology Co., Ltd. is one of the largest adhesive manufacturers in zhejiang China. Excellent location for us to get more high quality resources such as raw materials human capital and latest technology. The company covers an area of 12000square meters, with construction area of 8000 square meters is a company with an integration of science, industry and trade.