| Type: | Professional Amplifier |
|---|---|
| Usage: | Hi-Fi, AV, KTV System |
| Used For: | Professional |
| Tube Type: | Transistor Amplifier, IC Amplifier |
| Function: | Post Amplifier, Amplifier Combined, Pre-amplifier |
| Sound Channel: | 4.1, 2CH/4CH |
| Customization: |
|---|
Suppliers with verified business licenses
Audited Supplier
P series amplfier is Class-AB power amplifier. 1.Sexy and novel appearance. 2.Intelligent soft boot,sophisticated short-circuit,over-load,over-heat protection. 3.Compact steel frame,shockproof,compressive resistance. 4.With built-in low frenquency exciter. 5.Be able to work in stereo,paraleel and bridge mode.
TECHNICAL PARAMETER OF P SERIES AMPLIFIER:
1. Mains Power Switch
When press the switch, the soft start circuit run for avoiding surge strike. In about 3-4 seconds, there will be a clicking denote that soft start finished. And more 1-2 seconds later, there will be another "clicking", the amplifier is connected with speaker and ready to work.
2. CH-1/CH-2 Input level control
Adjust it to get the volume desired. Use CH-1 control only while amplifier is set in Bridge or Parallel mode.
3. CH-1/CH-2 Protection indicating LED
This red LED will light up when the amplifier is running un-stable or went in to thermal protection after the power elements temperature over 90ºC.
4. Clip LED
Turns on just before the maximum, distortion free, output level of the amplifier. The clip Leds may turn on shortly from time to time but they may certainly not turn on for longer periods. In this case you have to turn the output level down!
5. Signal LED
The green signal led indicates that a music signal is present at this channel input.
6. Stereo mode indicating LED
These green LED will light up while the input signal is connected, the amplifier is working under stereo mode.
7. Parallel mode indicating LED
Indicate that the amplifier is working under parallel mode, the indicator is lighten, input signal only acts on CH-1.
8. Bridge mode indicating LED
Indicate the amplifier is working under BRIDGE mode, the indicator is lighten , and the input signal only acts on CH-1
1. CH-1/CH-2 input XLR
standard XLR jack, bleow is the connection method;
Pin1: signal groud, Pin2: signal+, Pin3: signal-
2. CH-1/CH-2 Signal Link Output
Standard XLR (male) socket for input signal link, its Pins parallel connected with the female XLR socket so you can feed the same signal to another amplifier. Pin1: signal groud, Pin2: signal+, Pin3: signal-
3.Mode1/mode2
Two limiter mode.
4. CH-1/CH-2 35Hz HPF.
The low cut filter cuts all undesired frequencies below 35Hz.protecting woofers against excesslve swings.
5. Output Mode Set Switch.
Select the run mode as STEREO or BRIDGE or PARALLEL
6. CH-1/CH-2 SUB Processor
Controls the amount of low band signal, produced by the bass processor, from zero to maximum. The setting depends on the application and can be adapted to your own taste.
7. CH-1/CH-2 output speakon
Standard Speakon socket. 1+ 2+ :, 1- 2-: -
8. Binding post outputs
These posts will accept bare wire cables that connect to your speakers.
9. Recoverable fuse
This fuse will automatic break to stop amplifier running when there was a failure.
After failure removed, press the fuse button to set the fuse back to normal condition
10. Mains Power Supply Cord
Branch Company - Guangzhou MingXuan Audio Co., Ltd was established in 2012. Mingxuan Audio is focus on high quality audio products such as speaker, amplifier, mixer, microphone, especially outdoor high-power active speakers.
There are professional design team, sales team, customer service team and technical team to service all customer . Based on high quality & competitive prices & better service, our products have entered the Americas, Europe, Asia, Africa markets successfully, such as USA, Canada, UK, Germany, France, Singapore, Japan, Nigeria etc, and get good feedback.
1. Provide professional person to communicate with you before the order.
2. Provide strict quality check for each part, each process before export.
3. Provide optimum system solution based on each client's specific requirement.
4. Provide complete post-sale service, including installation, technical guide and training.
You can choose flight case packing
Q: Do you offer guarantee for the products?
A: Yes, we offer 2 years warranty to our products.
Q:What is your product range?
A:We are mainly offer all kind of stage lighting and audio-visual equipment etc.
Q: Can you help me to print our logo or company name on the products or package?
A: Of course. Your logo can be printed on the products or package.
Q: If the products broken during the warranty, what should I do?
A: If there is a problem with the products, please describe it and send videos or pictures to us to analyze. Then we will guide you how to fix it and provide spare parts on free if needed.
Suppliers with verified business licenses
Audited Supplier 
){kind=link}
){kind=link}