Factory Price 200W DMX512 Disco Lighting Party Light Stage DJ Equipment Club Lighting Fixture LED Moving Head Light

MF-DM200W LMB BEAM SHARPY MOVING HEAD LED STAGE LIGHT

Product Parameters

CHANNEL TABLE

CHANNEL	24 CHANNEL PATTERN
1	Color
2	Strobe
3	Dimming
4	Gobo
5	Prism 1
6	Prism 2
7	Prism 1 Rotate
8	Prism 2 Rotate
9	Frost & Colorful
10	Focus
11	X
12	X Fine
13	Y
14	Y Fine
15	XY Speed
16	Reset
17	LED Dimming
18	LED Strobe
19	LED Red
20	LED Green
21	LED Blue
22	LED Color Macro
23	LED Scene
24	LED Scene Speed

TECHNICAL SPECIFICATION

Voltage	AC200-240v 50/60Hz
Power of Light Source	200W
Color Disk	Each color disk consists of 14 color plates + white light
Pattern Plate	10 gobos with 3 glasses gobos+ white
Control Mode	DMX512/ master-slave/Automatic
IP	20
Protection	Overheat Protection
540° translation, 270° tilt

Common Faults

According to some common faults, the corresponding solutions are put forward.Any

unsolvable problems should be dealt with by professionals.Disconnect the light fixture

before maintaining it.

1. Light bulb is not on

Check that the voltage that matches the light fixture is installed;

Check whether the lamp supply power connection or control switch is in bad contact;

Check if the power supply is insufficient;

Check that the DMX512 controller is sending instructions.

 

2. The light fixture does not accept control from the console after normal reset

Check luminaire digital start address value and function options are correct;

Check whether the connection of communication control line is correct, the communication line is too long or has been interrupted;

Check whether the control equipment is invalid, check whether the serial access signal amplifier is invalid;

Check whether the communication line is too long or other equipment interferes with each other;

Optimize wiring, shorten the length of control signal lines, high voltage and low voltage lines separate wiring

Add signal amplifiers;

Signal line using high-quality shielded twisted pair wire;

Connect the signal terminal resistor (120 ohm) at the end of the lamp.

3. Luminaire does not start

Check that the power supply parameters are consistent with the lamp;

Check the poor contact caused by extrusion deformation, vibration and moisture of internal parts in the long distance transportation process or fall off.

Please check whether the internal wire integration connector of the lamp has fallen off or loosened.

Check whether the electronic components of the lamp (such as electronic transformer, PCB board, motor control board, etc.) are loose, short circuit and burned out.

 

 

4. When working, the action of the X or Y axis of the lamp is not normal 
Follow the previous step to check them one by one;

Check whether the transmission belt corresponding to the X and Y axis directions in the lamp falls off and breaks;

Check whether the data feedback receiver (optocoupler) 

corresponding to the X and Y directions in the lamp is damaged;

Restart the machine and reset it once.

 

 

Options	Instructions
Running Mode	DMX	Slave state: Receives DMX signals from the console or mainframe
	Bootstrapping	Host state: Self-actuated and sends DMX signal to slave
	Voice Control
DMX Address	1-512	Press "OK" to enter editing mode.At this point, the hundreds digit is selected, and press the "up" and "down" keys to change the address code.Press the "OK" key again  to select the tens edit.Press "OK" once more to select the ones edit.Press again to exit the editing state
Motor Reset	off
	on	Light fixture reset
Channel mode	24CH	24 channel mode
Language	Chinese	Set to the Chinese interface
	English	Set to the English interface
Screen Flip	off	Front display
	on	Screen reverse display
X Inversion	off
	on
Y-reverse	off
	on
XY Swap	off
	on	Channel for switching XY axes (including trims)
XY Encoder	on	Use an encoder (optocoupler) to judge out of step and automatically correct the position
	off	Correct the position without using an encoder (optocoupler)
DMX Signal	Hold	Continue running in its original state
	Clear Zero	Turn the motor back and stop running
The color wheel changes linearly	on	The color wheel changes linearly
	off	Color wheel nonlinear change, half color change
Restore Default Settings		When you see the confirmation dialog after pressing "OK", press "OK" again to restore the default Settings

INSTALLATION

Light fixtures can be placed horizontally, slanted, and hung upside down. Be sure to pay attention to the installation method when hanging diagonally and upside down.

As shown in Figure 2, before positioning the lamp, it is necessary to ensure the stability of the installation site. When installing the reverse hanging, it is necessary to ensure that the lamp does not fall down on the support frame. It is necessary to use the safety rope through the support frame and the lamp handle for auxiliary hanging to ensure safety. Prevent the

luminaire from falling and sliding.

When installing and debugging the lamps, it is forbidden for pedestrians to pass under them. Regularly check whether the safety rope is worn and whether the hook screws are loose.

Our company does not assume any responsibility for all consequences caused by the fall

of the lamp due to the unstable installation of the hanging

CONTROL PANEL

The following takes "Modify DMX address code" as an example to describe the use of keys:

1. If the current is not the main interface, press the "left" key (one or more times) to return to

the main interface

2. In the home screen, press the "up" key or "down" key to select the "Settings" button

3. Press the "OK" key to enter the "Settings" interface

4. In the "Settings" interface, press the "up" key or "down" key to select "DMX address"

5. Press the "OK" key to enter the editing state

6. Press the "up" key or "down" key to modify the DMX address code

7. Press the "OK" key to exit the editing state

Detailed Photos

 

Important: The wires should not touch each other or the metal housing.

PACKING LIST

UNPACKING INSTRUCTIONS
On receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are presented, and have been received in a good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows, sign of mishandling. Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture should be returned in original factory box and packing.

SAFETY INSTRUCTIONS
Please read these instructions, it includes important information about the installation, usage and maintenance of this product. 

Please keep this user guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet.

Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture.

Before the first time to use it, Please check whether the damage in transit, if happen damages in transit, please do not use this lamp, and please asap contact distributors or manufacturers.

Please don't install the lamp in the ordinary combustible material on the surface.

Lamp should be installed in the well ventilated place, and the distance of the wall to keep it over 10 cm, at the same time, please check the fan hole was clear.

Do not use lamp direct project in flammable objects, lamp and the radiation of the distance between the objects please keep it over 12 m.

Do not use direct lamp project light source , to avoid damage the eyes. Before installation, please make sure your use power supply voltage and marked voltage

Note: before any install, maintain and clean lamp, please confirm cut off the power supply

SHIPPING

Ming Feng Lighting Co., Ltd. is a leading LED lighting manufacturer with its own factory. Our company specializes in the design, production, and distribution of high-quality LED lighting products. With years of experience in the industry, we have established a reputation for excellence and innovation in LED lighting technology. Our team of skilled professionals is dedicated to providing customers with the best LED lighting products and services. At Ming Feng Lighting Co., Ltd., we pride ourselves on our commitment to quality and customer satisfaction. Whether you are looking for residential or commercial LED lighting solutions, we have the expertise and resources to meet your needs.

Q1: What do you sell?
A1: We provide good quality of floodlight, high bay light, explosion proof light, tri-proof light, downlight, and other lighting products, as well as responsible services and reliable after-sales warranty.

Q2: Is it OK to print my logo on led light product?
A2: Yes. We provide ODM and OEM services. Please inform us formally before our production and confirm the design firstly based on our sample.

Q3: How to deal with the faulty?
A3: During the guarantee period, we will send new lights with new order for small quantity. For defective batch products, we will repair them and resend them to you or we can discuss the solution including re-call according to real situation.

Q4: Can I have a sample order for led light?
A4: Yes, we welcome sample order to test and check quality. One sample or mixed samples are acceptable.

Q5: How long time to ship the goods if place an order?
A5:  Usually 7 days for sample or small order,15 working days for bulk order, but sometimes depend on the order quantity.