Solar Keymark EN12976 certified Compact Heat Pipe Solar Heating System for Chile100L to 300L Heat Pipe Solar Hot Water Heater System
HIGH PRESSURE HEAT PIPE SOLAR WATER HEATER MAKE BETTER BATHING EXPERIENCE.
1.Solar Water Heater Work Principle:The key of compact heat pipe pressure solar water hater is heat pipe, The heat pipe is hollow with the space inside evacuated, much the same as the solar tube. In this case insulation is not the goal, but rather to alter the state of the liquid inside. Inside the heat pipe is a small quantity of purified water and some special additives. At sea level water boils at 100oC (212oF), but if you climb to the top of a mountain the boiling temperature will be less that 100oC (212oF). This is due to the difference in air pressure.
Based on this principle of water boiling at a lower temperature with decreased air pressure, by evacuating the heat pipe, we can achieve the same result. The heat pipes used in AP solar collectors have a boiling point of only 30oC (86oF). So when the heat pipe is heated above 30oC (86oF) the water vaporizes. This va pour rapidly rises to the top of the heat pipe transferring heat. As the heat is lost at the condenser (top), the va pour condenses to form a liquid (water) and returns to the bottom of the heat pipe to once again repeat the process.
The top of heat pipe is pluged into the water tank, so the cold water inside the tank can get heat from heat pipe, and become hot water. Because the water tank is close, so it can endure 0.6Mpa(6 bar), when the tap go into the water tank from the bottom inlet, the hot water is out from the top outlet, just like the electric water heater.1, direct heating, high efficiency
2, pressurized hot water
3, Non-Freeze in winter
4, CE, SOLAR KEYMARK EN12976 certified
5, Factory audited by SGS.
2.Compact Heat Pipe Solar Hot Water Heater System Feature
1)Highly efficient absorber of high performance with daily average efficiency over 50%.
2)Start quickly, heat pipe transfers the heat energy into the storage tank in one direction.
3)With stand pressure of 6 bar, can be connected directly with tap water.
4)No water inside the vacuum tubes, the system can still work even with several tubes breakage.
5)Highly efficient insulation with polyurethane foam.
6)Simple structure, easy to assemble and install.
7)Can be used all year around in the cold climate.
8)Can be used together with auxiliary electric heater.
9) Stable and reliable performance.
10) Environmental protection and energy saving.
11) The pressurized hot water will make your bath more comfortable.
3. Solar Water Heater Combined with House
4. Solar Water Heater Loading and Package
SOLAR WATER HEATER Package details: poly bag wrapped, Styrofoam underlay, export carton packed.
5. Solar Water Heater CAPACITY and LOADING QUANTITY GUIDE(20'GP container, 40'GP container, 40'HQ container)
|Model||Tube Specification||Capacity||Loading quantity|
|Technical Parameter of Heat Pipe Compact Pressurized Solar Water Heater|
|DESCRIPTION||Compact pressurized solar water heater|
|MATERIAL OF OUT TANK||0.4mm galvanized steel/0.4mm sus304 stainless steel /0.4mm sus304-ba(bright)|
|MATERIAL OF INNER TANK||1.2mm sus304-2b stainless steel or sus316 stainless steeel|
|TANK INSULATING LAYER||50-60mm high-density polyurethane foamed|
|DIAMETER OUTER/INNER TANK||470/370mm |
|ELECTRICAL HEATER||1500w; 220v/110v|
|INLET AND OUTLET HOLE||Male 1/2", 3/4"|
|SOLAR COLLECTOR TUBE||3.3 borosilicate glass with AL/AL-ALN/ALN(single target) or CU/SS-ALN/ALN(three target)|
|THICKNESS OF GLASS TUBE||1.6mm|
|VACUUM TUBE TIGHTNESS||P≤0.005 pa|
|EMISSION RATIO||Ε h=0.04-0.06(80c± 5c)|
|IDLE SUNNING PROPERTY PARAMETERS||Y=220~260m². C/kw|
|AVERAGE HEAT LOSS COEFFICIENT||Ult=0.6~0.7w/(m2. c)|
|BRACKET:||1.2mm Stainless steel/1.6mm aluminum alloy/1.5mm galvanized steel|
|STRUCTURE OF TANK:||Usually holes for p/t valve, water inlet and outlet, electric heater, magnesium rod; custom-built will be warmly welcomed.|
|WELDING:||Automatic argon arc welding|
|FASTENER PIECES:||Stainless steel screw|
|SEAL MATERIAL||Stabilized high temperature silicon|
|Opition:||System controller SR609C, control electrical heating and display temperature|
1, Fast delivery, 40 feet container quantity will deliver in 7 days.
2, Experienced sales team assistant you, fast confirmation for every related questions from you.
3, Rich experiences for differenct Market (countries), kinds of customized design will be welcomed.
4, Assistant you load other goods with solar water heater in one container.
5, Installation guide and train
6, LOGO print and water tank and cartons.
1. Is solar water heating a viable alternative to gas or electricity?
Solar should not be seen as a alternative to gas or electricity, but rather a supplement. Solar cannot totally replace the need for gas or electric heating as there are sometimes days when there is little sunlight. When averaged over a year, a correctly sized solar system can provide 60%-70% of a household's hot water needs. Providing more than this is unadvisable, as too much heat will be produced in the summer. The hot water system system can easily be automated so hot water is guaranteed regardless of sunlight levels.
2. How long will it take to recoup my investment?
QIRUI solar collectors are much more affordable than many other solar hot water heaters. For a household of 4, the price of a full system may not be too much more than a new electric or gas system. Depending on you location (solar levels) and current hot water usage the annual electricity or gas saving will differ. However in a normal household that spends 25% of its electricity bill on hot water heating, the full cost of the purchase may be recouped as quickly as 4-5 years in reduced bills. You will definitely make considerable savings during the life of the solar hot water heater.
3. Can QIRUI solar collectors be used in cold conditions?
Yes. QIRUI collectors can be used in temperatures as low as -30oC, although performance is greatly reduced in such extreme conditions. Good heat output is still achieved in mild sub-zero conditions.
4. What happens if one of the tubes is broken?
Firstly, tubes are very strong and not easily broken, but if the worst should happen, solar tubes can be replaced very easily. They are inexpensive and available though your local QIRUI distributor. The HAINING QIRUI solar collectors can operate with several broken tubes, but the efficiency will be reduced, so it is recommended that broken tubes be replaced immediately.
5. Will water be heated on a cloudy day?
Yes. Although the heat output of the solar collector is reduced on overcast days it will still be able to provide heating. If it is a heavily clouded day or raining, then more gas or electric boosting may be required to maintain water at the required temperature. This system will be automated so you don't have to worry about running out of hot water on a rainy day.
6. Can I use a solar collector with my existing hot water system?
Normally yes. Simple retrofit valves can often be used to allow solar to connect to your existing cold water inlet. If your tank cannot accept the solar input directly an additional storage tank can be installed to pre-heat the cold water prior to entering the existing tank.
7. Are the solar collectors noticeable on the roof?
If only the collector is mounted on the roof it should blend into the roof design quite well. HAINING QIRUI solar collectors are very thin and can be flush mounted on a roof. From a distance they look somewhat like a skylight. You may have to check with your local council regarding building restrictions when installing your solar collector. Click here to view installation photos.
8. Can QIRUI solar collectors be mounted on a flat surface?
Yes they may be mounted on a flat roof, or on the ground by using a stainless steel Flat Roof Frame. The collector should be installed at a minimum of 20o angle to ensure optimal heat pipe operation.
9. How do I protect my solar system during subzero temperatures?
If you have a system that is operating in areas with subzero temperatures then freeze protection must be implemented. The easiest means of preventing freezing is to use a controller with a low temperatures setting, so when the manifold temperature drops below a certain pre-set temperature (5oC/40oF), the pump will circulate, warming the collector with water from the bottom of the storage tank. The pump will not run continually, just periodically, the frequency of which will depend on the outside temperature. In extremely cold areas, a closed loop using a glycol/water mix may be appropriate.
10. Will the QIRUI solar collector be a fire hazard during hot, dry weather?
No. The QIRUI solar collector's components are all high temperature rated and non-flammable so even during strong sunlight with the circulation pump turned off (stagnation), the system will not catch alight or give off any sparks. The majority of the solar collector's components are stainless steel, aluminium, glass or glass wool. The manifold outlet should be fitted with a temperature relief valve, which will prevent the manifold temperature from exceeding 99oC / 212oF.