Basic Info.
Dji Air Unit Connection Way
Two Ways Supported: 6-Pin Connector or Direct
Continuous Current
55A * 4
Burst Current
60A(10seconds)
ESC Protocol
Dshot300/600
Transport Package
Standard
Specification
F722 FC with 4 in 1 ESC
Product Description
F722 Flight Controller stack with 55A 4 in 1 ESC
Description:- -ESC: The continuous current of 55A 4 in 1 ESC is 60A*4, the burst current is 60A for 10 seconds. Support 3~6S lipo and Dshot300/600 PWM.
- -LED Pad: Supported LED, 5V, and GND pads are on the bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware and INAV firmware, made your model fly at night.
- -GPS & 16M Blackbox: Equipped with a GPS pad and 16M black box, after you solder up your GPS, you can track the flight trajectory of your model and the black box will record the flight process.
- -Firmware: The firmware is Betaflight Configurator. You can connect the flight controller stack with your computer to adjust and observe the data that you want.
- -Parameter: The MCU is STM32F722RET6, IMU is MPUICM42688. The mounting dimension is 30.5 x 30.5mm, hole diameter is 4mm. You can according to these choose whether it fits your models or not.
SpecificationsF722 30.5x30.5 Flight Controller
MCU | STM32F722RET6 |
IMU(Gyro) | ICM42688 |
USB Port Type | Type-C |
Barometer | BMP280 |
OSD Chip | BetaFlight OSD w/ AT7456E chip |
DJI Air Unit Connection Way | Two ways supported: 6-pin connector or direct |
6-pin DJI Plug | Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed. |
Black box | 16M Black Box |
Current Sensor Input | Supported. For 60A ESC, please set scale = 180 and Offset = 0. |
Power Input | 3S - 6S Lipo(Through ESC 8-PIN connector) |
5V BEC Output | 5 grous 5V output,the total current load is 3A |
9V Output | 3 groups 9V output,the total current load is 2.5A |
3.3V Output | 1 group 3.3V output,maxmum current is 300mA |
ESC Signal | M1 - M4 |
UART | 6 sets(UART2 UART5, UART3), UART6(Dedicated for SBUS), UART4(Dedicated for ESC telemetry),UART1 (Dedicated for VTX data setting) |
Sbs | Debugging to UART6 Channel |
ESC Telemetry | UART R4(UART4) |
I2C | Supported. SDA & SCL pads on front side. Used for magnetometer. |
LED Pad | Supported. LED,5V, and GND pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware. |
Buzzer | supported,5V,BZ pads for 5V Buzzer |
BOOT Button | Supported. |
Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked. |
When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware. |
Supported Flight Controller Firmware | BetaFlight(Default), |
Firmware Target Name | STM32F722RET6 |
Mounting | 30.5 x 30.5mm( 4mm hole diameter) |
Dimension | 37(L) x 37(W) x 6.6(H)mm |
Weight | 7.5g |
BLS 60A 30.5x30.5 4-in-1 ESCFirmware | BLS 16.7 |
Continuous Current | 55A * 4 |
Burst Current | 60A(10seconds) |
TVS Protective diode | Yes |
External Capacitor | 35V1000uF Low ESR Capacitor(In the package) |
ESC Protocol | DSHOT300/600 |
Power Input | 3-6S LiPo |
Power Output | VBAT |
Current Sensor | Support (Scale=180 Offset=0) |
ESC Telemetry | Not supported |
Mounting | 30.5 x 30.5mm( 4mm hole diameter) |
Dimension | 42.3(L) * 37(W) * 6.2mm(H) |
Weight | 12g |
Address:
Room 4, 14th Floor, 1st Building, No. 699, Kenong Road, Shenzhen, Guangdong, China
Business Type:
Manufacturer/Factory
Business Range:
Computer Products, Consumer Electronics, Electrical & Electronics, Instruments & Meters
Company Introduction:
Igmic Co., Limited is a company located in Shenzhen, a high-tech research and development, design, and manufacturing center in China. The company can provide drone complete machines and accessories manufacturing, such as motor, flight control, image transmission, electronic speed controllers, etc.
Based on the rapid product development and excellent product quality control and manufacturing capabilities in Shenzhen, China, we can provide you with end-to-end small batch customization and ID based design customization services (OEM/ODM service).
We have established long-term cooperative relationships with over 160 clients around the world.
We would like to grow up with you, and gain mutual benefits. Your valuable comments and ideas would be appreciated.
Please contact and join us to achieve your dreams and create success!