Features Hot pluggable10Gb/s serial optical interface compliant to 802.3ae 10GBASE-ER/EW1550nm cooled EML transmitter with TEC, PIN photo-detectorUp to 40km on 9/125um SMFSFP+ MSA package with duplex LC connector2-wire interface for management and diagnostic monitorSFI High Speed Electrical InterfaceVery low EMI and excellent ESD protection+3.3V single power supplyPower consumption less than 1.5WOperating case temperature: 0~+70°C
Applications10G Base-ER/EW10G Fiber Channel (with/without FEC)10G Storage system
StandardCompliant to SFP+ SFF-8431 and SFF-8432Compliant with SFF-8472 Rev 10.2Compliant with IEEE 802.3ae 10GBASE-ER and 10GBASE-EWCompliant with IEC 60825-1 Class 1 laser eye safe RoHS Compliant
Description
HSFP10-1541-L-ECI is 1550nm cooled EML laser based 10Gigabit SFP+ transceiver , which is designed to transmit
and receive optical data over single mode optical fiber for link length up to 40km.
The SFP+ ER module is small form factor pluggable module for duplex optical data communications such as
10GBASE-ER/EW defined by IEEE 802.3ae. It is with the SFP+ 20-pin connector to allow hot plug capability.
The transmitter input and receiver output impedance is 100 Ohms differential. Data lines are internally AC
coupled. The module provides differential termination and reduce differential to common mode conversion for
quality signal termination and low EMI.
The transmitter converts 10Gbit/s serial PECL or CML electrical data into serial optical data compliant with the
10GBASE-ER standard. An open collector compatible Transmit Disable (Tx_Dis) is provided. A logic "1," or
no connection on this pin will disable the laser from transmitting. A logic "0" on this pin provides normal
operation. The transmitter has an internal automatic power control loop (APC) to ensure constant optical power
output across supply voltage and temperature variations. An open collector compatible Transmit Fault
(Tx_Fault) is provided. TX_Fault is a module output contact that when high, indicates that the module
transmitter has detected a fault condition related to laser operation or safety. The TX_Fault output contact is an
open drain/collector and shall be pulled up to the Vcc_Host in the host with a resistor in the range 4.7-10 kΩ.
TX_Disable is a module input contact. When TX_Disable is asserted high or left open, the SFP+ module
transmitter output shall be turned off. This contact shall be pulled up to VccT with a 4.7 kΩ to 10 kΩ resistor
Absolute Maximum Ratings
Parameter | Symbol | Min | Max | Unit |
Storage Temperature | TST | -40 | +85 | ºC |
Supply Voltage | VCC3 | 0 | +3.6 | V |
Relative Humidity | RH | 5 | 95 | % |
Recommend Operation Environment:
Parameter | Symbol | Min | Typ | Max | Unit |
Date Rate | | | 10.3125 | | Gb/s |
Supply Voltage | VCC | +3.14 | 3.3 | +3.47 | V |
Supply Current | ICC | | 380 | 450 | mA |
Power Dissipation | PD | | | 1.5 | W |
Operating Temperature | TOP | 0 | 25 | +70 | ºC |
Transmitter Operating Characteristic-Optical, Electrical
Parameter | Symbol | Min | Typ | Max | Unit | Ref. |
Side Mode Suppression Ratio | SMSR | 30 | - | | dBm | |
Average launch power of OFF transmitter | Poff | | - | -30 | dBm | |
Extinction Ratio | ER | 8.2 | - | - | dB | |
Transmitter Dispersion Penalty | TDP | - | - | 3.0 | dB | |
Operating Data Rate | S | | 10.3125 | | Gbps | |
Centre Wavelength | λC | 1520 | 1550 | 1575 | nm | |
Spectrum Band Width (RMS) | σ | | | 0.45 | nm | |
Average Optical Power | Pavg | -4.7 | - | 4.0 | dBm | |
Optical Eye Mask | Compliant with IEEE 802.3ae | |
Input Differential Impedance | ZIN | 90 | 100 | 110 | Ω | |
TX Disable | Disable | | 2.0 | | Vcc+0.3 | V | |
Enable | | 0 | | 0.8 | V | |
TX Fault | Fault | | 2.0 | | Vcc+0.3 | V | |
Normal | | 0 | | 0.8 | V | |
Data Dependent Input Jitter | DDJ | | | 0.08 | UI | |
Data Input Total Jitter | TJ | | | 0.25 | UI | |
Receiver Operating Characteristic-Optical, Electrical
Parameter | Symbol | Min | Typ | Max | Unit | Ref. |
Center Wavelength | λr | 1265 | | 1600 | nm | |
Average receiver power | PIN | | | -15.8 | dBm | |
Receiver Overload | PMAX | -1.0 | | | dBm | |
Receiver Reflectance | | - | - | -26 | dB | |
Los Assert | LosA | -30 | | - | dBm | |
Los Dessert | LosD | | | -16 | dBm | |
Los Hysteresis | LosH | 0.5 | 2 | 5 | dB | |
Receiver Reflectance | | | | -26 | dB | 1 |
Output Differential Impedance | PIN | 90 | 100 | 110 | Ω | |
LOS | High | | 2.0 | | Vcc+0.3 | V | |
Low | | 0 | | 0.8 | |
Rx Output Rise and Fall Time | Tr/Tf | 30 | | | ps | 20% to 80% |
Total Jitter | TJ | | | 0.7 | UI | |
Deterministic Jitter | DJ | | | 0.42 | UI | |