LPCB security fire system addressable host alarm panel Introduction: The purpose of the AW-FP300Fire Alarm Control Panel (FACP) is to monitor input signals, give indications and possibly activate outputs as programmed. It is designed to comply with EN 54-2 with qualities of simple installation, operation and easy maintenance. The AW-FP300panel is an addressable fire detection panel with 1 loop of 324 addressable points and expansion capabilities.It is compatible with other peripherals made by ASENWARE with its own protocol. Features: The AW-FP300 single loop 32 zone fire alarm control panel offers the following features: 1. Up to 324 addresses on one loop 2. An easy to read, 4.3'' color screen LCD with a resolution of 480&times;272 3. Zone indication and control panel(ZCP) for 32 zones gives a quick indication of the location of an alarm 4. Record capacity of 1000 historical events for each of historical fire, historical fault and historical operation 5. An independently programmable conventional sounder circuit output 6. Integral power supply and battery 7. Integral printer 8. Flexible and intuitive cause and effect programming on front panel 9. Zone test, point test and module start/stop testing facilitate the commissioning 10. U-disk interface makes the load and save of configuration or historical data convenient for system commissioning and maintenance 11. Hierarchy management with three access levels 12. Anti-tamper protection by a key lock 13. CAN bus for interconnection of up to 20 FACPs and RS485 for connection with up to 30 fire indicating panels per FACP Parameters: Power supply Mains supply 230VAC (-15%, +10%). 47 ~ 63Hz. Max current 0.8A Mains fuse T3.15AL250V Operating voltage 18.5 ~ 30VDC Recommended mains cable Screened or standard/black mains cable, cable size 0.75mm2 Power rating Imax.a=1.2A; Imax.b=2.6A; Imin=0.65A Max. charging current 1.2A Max. battery supply current 4A (when the Mains is disconnected) Battery capacity, type and recommended model Max. capacity 2&times;12V/17Ah; Min. capacity 2&times;12V/12Ah VRLA. PS-12170 for 17Ah (Power-sonic), PS12120 for 12Ah (Power-sonic) Max. internal resistance of battery 1.5&Omega; Battery fuse F8AL250V Recommended battery cable 14AWG Quiescent current (full loaded) < 0.4A Outputs S.C. Out (+, -) Output voltage 18.5 ~ 30VDC Max. output current 0.5A Fuse rating F1AL250V End of line resistor 4K7 Recommended type of cable Plain unscreened cable, 1.5mm2 Cable diameter 1mm2 ~2mm2 Transmission distance &le;1500m Max. number of sounders @50mA 20 F.P.E. Out (+, -) F.A. Out (+, -) Output voltage 18.5 ~ 30VDC Max. output current 0.5A Fuse rating F1AL250V End of line resistor 4K7 Recommended type of cable Plain unscreened cable, 1.5mm2 Cable diameter 1mm2 ~2mm2 Transmission distance &le;1500m Fault Out (NC, COM, NO) Contact capacity 30VDC@2A, [email protected] Recommended type of cable Plain unscreened cable, 1.5mm2 Cable diameter 1mm2 ~ 2mm2 24VK (+, -) Output voltage 18.5 ~ 30VDC Max. output current 0.6A Fuse rating F1AL250V Recommended type of cable Plain unscreened cable, 1.5mm2 Cable diameter 1mm2 ~2mm2 Input Class change (+, -) Input mode Passive Cable resistance &le;500&Omega; Recommended type of cable Plain unscreened cable, 1.5mm2 Cable diameter 1mm2 ~2mm2 Loop Loop Out (+, -) Loop In (+, -) Output voltage 16.5 ~ 30VDC, pulse Output current 0 ~0.3A Loop type Class A Recommended type of cable Screened or unscreened twisted-pair, 1.5mm2 Transmission distance &le;1000m Cable diameter 1mm2 ~2mm2 Network communication RS-485 Max. number of FIP